宁夏红寺堡盆地隐伏古隆起成因机制及其对区域沙漠化的影响

目前对于青藏高原东北缘活动构造研究多集中于活动断裂带的活动性,而对夹持于其间的沉积盆地构造格架及活动性研究甚少。以夹持于烟筒山断裂与牛首山—罗山断裂之间的宁夏红寺堡盆地为研究对象,采用重力资料重处理解译、音频大地电磁测深(AMT)和地震勘探相结合,揭示红寺堡盆地隐伏构造特征,并进一步采用盆山一体化思路分析隐伏构造的成因机制及其对区域沙漠化的控制作用。结果表明:青藏高原在中新世末发生强烈的NE向推挤、扩展和隆升,红寺堡盆地由坳陷盆地转变为挠曲盆地; 在青藏高原NE向扩展的影响下,烟筒山断裂发生强烈的逆冲作用,古生代—中生代基底逆冲于古近系—新近系之上,受构造变形影响的最新地层为中新统彰恩堡组; 红寺堡盆地内的隐伏古隆起呈NW—SE向,与烟筒山构造带具有相同的构造动力学背景,受青藏高原NE向扩展影响形成于中新世末,并且至今仍具有活动性; 隐伏古隆起周缘断裂的活动破坏了地表稳定性、蓄水能力和地表植被,导致区域沙漠化呈现有规律的NW—SE向带状展布。该研究成果对于宁夏红寺堡盆地区域稳定性评价及沙漠化的综合治理具有现实指导意义。     

聚乙烯醇/牛I型胶原支架材料的制备及评价

研究了一种聚乙烯醇(PVA)和胶原(COL)复合支架材料的制备方法。采用氨基硅烷对PVA海绵表面进行了氨基化修饰后，通过戊二醛溶液交联牛Ⅰ型胶原(COL)，最后通过赖氨酸溶液封闭，获得一种PVA/COL复合支架材料。采用扫描电镜(SEM)、X光电子能谱仪(XPS)、傅里叶红外光谱(FT-IR)等手段对支架材料的理化性能进行表征，并通过细胞实验对支架材料的生物学性能进行评价。结果表明，经过COL修饰的PVA孔隙率为21.33%，平均孔径为168.68 ?m且均匀分布，支架材料接触角为20.03°。对支架材料的生物学评价结果表明C3A细胞在复合材料上黏附良好，优于PVA组；CCK-8增殖检测结果表明细胞在复合材料上呈增殖生长趋势，与对照组PVA相比差异显著(P?0.01)。将PVA和COL复合制备得到的支架材料具有良好的理化及生物学特性，具有广阔的应用前景。     

抗硫化返原剂PK900在全地形轮胎胎面胶中的应用

研究抗硫化返原剂PK900在全地形轮胎胎面胶中的应用。结果表明:在全地形轮胎胎面胶中添加抗硫化返原剂PK900,胶料硫化速度变化不大,抗硫化返原性能提高,在过硫条件下硫化胶可保持较好的物理性能;成品轮胎的耐久性能提高,使用寿命延长。     

机翼极限环颤振的CFD/CSD全隐式紧耦合方法

针对轴承振动实时状态监控的需要，从符号动力学角度提出了符号聚合近似与Lempel-ziv复杂度（SAX-LZC）融合的振动监控参数。首先，以Logistic映射和Duffing方程为对象，从理论角度验证了SAX-LZC对动力学结构表征的准确性，并验证了该指标的抗噪能力和计算效率；其次，将SAX-LZC指标与信息熵、样本熵、多分段Lempel-ziv复杂度等动力学参数性能进行了综合对比；最后，从实验角度对轴承早期微弱异常进行了监测，并对轴承典型故障进行了特征提取。理论研究结果表明，SAX-LZC具有动力学结构表征准确、抗噪能力好、计算高效简洁等优点，克服了常规动力学参数工程应用能力弱的问题。实验研究结果表明，SAX-LZC对早期微弱异常有准确的监测，对不同种类故障具有较好的区分度，弥补了时域和频域对轴承微弱故障表征能力不足的缺陷，是一种轴承振动实时状态监控与故障特征提取的有效参数。     

中国省际绿色技术创新效率测度及影响因素研究

文章基于2011—2017年中国30个省份面板数据，运用super-SBM模型对绿色技术创新效率进行测算，并利用ML指数对绿色技术创新效率进行动态分析，最后通过空间滞后模型分析影响效率的关键因素。研究结果表明：中国绿色技术创新效率呈逐渐增长的趋势，但整体效率偏低，有较大进步空间；中国绿色技术创新效率存在明显区域差异，呈现由东部向西部递减的格局；绿色技术创新水平的提高是技术效率和技术进步共同贡献的结果；产业结构、区域开放程度和教育水平对绿色技术创新效率产生积极的正向影响，环境规制和研发投入强度对绿色技术创新效率影响不显著。     

Migration and distribution of saline ions in bauxite residue during water leaching

Bauxite residue, a highly saline solid waste produced from digestion of bauxite for alumina production, is hazardous to the environment and restricts vegetation establishment in bauxite residue disposal areas. A novel water leaching process proposed here was used to investigate the dynamic migration and vertical distribution of saline ions in bauxite residue. The results show that water leaching significantly reduced the salinity of bauxite residue, leaching both saline cations Na⁺, K⁺, Ca²⁺ and anions CO^2?₃, SO^2?₄, HCO^?₃. Na⁺ and K⁺ migrated from 40–50 to 20–30 cm of the column, presenting a high migration capacity. The migration capacity of Ca²⁺ was lower and accumulated at 30–40 cm of the column. CO^2?₃ initially distributed at 20–30 cm of the column, subsequently transported to 30–40 cm of the column, and finally returned to 20–30 cm of the column along with evaporation. SO^2?₄ was originally distributed at 40–50 cm, but finally migrated to 20–30 cm of the column. Nevertheless, HCO^?₃ remained at the bottom of the column, and its migratory was less affected by evaporation.     

Effect of Pre-cold Rolling-Induced Twins and Subsequent Precipitated x-Phase on Mechanical Properties in a β-Type Ti–Mo Alloy

This paper reported an effectiveness of pre-cold rolling-induced{332}\113[twins combined with subsequent isothermal x-phase formation for enhancement of uniform elongation in a b-type Ti–15Mo alloy with high yield strength level.Mechanical{332}\113[twins were induced by cold rolling with an thickness reduction of 5%,which had little effect on x-phase precipitation after aging at 573 K for 3.6 ks.Twinning after the cold rolling was further activated during tensile deformation,even with the presence of isothermal x-phase.This combination of twins and x-phase enhanced uniform elongation from 0 to 9%at yield strength level of 890 MPa.The high yield strength was mainly dominated by dislocation slip due to the isothermal x-phase formation,and early onset of plastic instability after yielding was hindered due to the pre-cold rolling-induced twins.Dynamic microstructural refinement was induced by further twinning activation during deformation,which resulted in high work hardening rate corresponding enhancement of uniform elongation.     

基于Faster R-CNN的颜色导向火焰检测

基于深度特征的目标检测方法Faster R-CNN在火焰检测任务上存在检测效率低的问题,因此提出了基于颜色引导的抛锚策略。该策略设计火焰颜色模型来限制锚的生成,即利用火焰颜色约束锚的生成区域,从而减少了初始锚的数量,提升了计算效率。为了进一步提高网络的计算效率,将区域生成网络中的卷积层替换成掩膜卷积。为了验证所提方法的检测效果,采用BoWFire和Corsician数据集进行验证。实验结果表明,该方法实际检测速度相较于原Faster R-CNN提高了10.1%,BoWFire上该方法的火焰检测F值为0.87,Corsician上该方法的准确度可达99.33%。所提方法可以提高火焰检测的效率,并能够准确检测图像中的火焰。     

A comparative study on the effect of loading speed and surface scratches on the flexural strength of aluminosilicate glass: Annealed vs. chemically strengthened

Quasi-static and dynamic three-point-bending experiments were conducted on both annealed and chemically strengthened aluminosilicate glass scratched by different normal loads. Scratched areas were observed by optical microscope and atomic force microscope. Chemically strengthened glass shows better resistance to surface scratch. These dynamic experiments were carried out using a modified Split Hopkinson Pressure Bar (SHPB) device and a pulse-shaping technique was used to keep constant loading speed to the specimens. In tests, high-speed photography was also used to observe the failure process of the specimens. The test results showed that the flexural strength of aluminosilicate glass (AG) strongly depends on the applied loading speed. Compared with its annealed counterpart, the chemically strengthened glass (CSG) showed higher flexural strength to both static and dynamic loadings. Moreover, the three-point bending experiments were conducted on scratched AG and CSG specimens and decrease of 20–40% in flexural strength was observed. The fractography analysis showed that in dynamic loading conditions the fracture surface was not smooth and has more secondary cracks as compared to static loading.